Multi-Tech Systems MTCBA-C-EN-NX User Manual Page 23
- Page / 60
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 3 – Using the Web Management Software
Multi-Tech Systems, Inc. MultiModem Wireless Modem with Ethernet Interface (S000375F) 23
General Configuration
Date and Time: The system date and time display in these formats: DD/MM/YYYY / HH:MM:SS. SNTP Client
must be enabled and you must have a live Internet connection for the date and time to display correctly.
IP Configuration
Enter the following addresses for the Ethernet interface.
IP Address (Default = 192.168.2.1), Mask (Default 255.255.255.0), Default Gateway (Default 0.0.0.0),
Primary DNS (Default 0.0.0.0), Secondary DNS (Default 0.0.0.0).
Note: See Appendix A – Table of Commonly Supported Subnets.
Auto Dialout Configuration
Auto Dialout: Check the box to enable/disable Auto Dialout. Default = Enable.
Raw Dialout: Check the box to enable/disable raw mode for an Auto Dialout session. Default = Disable.
Auto Dialout Login: Check the box to enable or disable Auto Dialout Login feature. Default = Enable.
Auto Dialout Port: Enter the serial Auto Dialout Port number. Default = 5000.
Handle EIA Signal: Check the box to enable/disable the EIA standard signal characteristics (time and
duration) used between different electronic devices.
Inactivity: Enter the time in seconds that the auto dialout session will stay active before going inactive.
Syslog Configuration
Syslog: Check the box to enable or disable Syslog. Default = Disable.
Syslog Server IP Address: If a Remote Syslog Server IP Address is specified, the syslog feature acts as a
remote Syslog.
Auto Discovery
Auto Discovery: Check the box to enable or disable Auto Discovery to broadcast (MAC level), the MAC
Address, IP Address, and DHCP information to the configured server port. Default = Enable.
Server Port: Enter the Server Port Number. Default port is 1020.
Broadcast Timer: Enter the amount of time in seconds for the auto-discovery packet granularity of periodic
broadcasting. Default is 10 seconds.
Auto Reboot Timer Configuration
Auto Reboot Timer: Enter the number of hours to lapse between each automatic reboot. The default of zero
deactivates the timer. Range is 0 to 999.
Telnet Configuration
Enables/Disables the Telnet port. The default is Enable.
Submit Button
Click the Submit button to save these settings. Note: You must click Save and Restart once you have
completed and submitted all the screens on which you have made changes.
IP Setup > HTTP Configuration
HTTP Configuration
HTTP Port: Enter the port number on which the HTTP server will listen for requests. Default is 80.
Authentication
User Name: Enter the User Name that can access to the Web Management software. Default is admin.
Password: Enter the Password for access to the Web Management software. Default is admin.
Note: You should change the password to one of your choosing. It can be up to 12 characters. Use a safe
password. Your first name spelled backwards is not a sufficiently safe password; a password such as xfT35$4
is better.
Submit Button
Click the Submit button to save these settings. Note: You must click Save and Restart once you have
completed and submitted all the screens on which you have made changes.
- MultiModem 1
- User Guide 1
- Table of Contents 3
- Chapter 1 – Introduction and 5
- Product Description 5
- Application Example 6
- Ship Kit Contents 6
- Safety Warnings 7
- Specifications 8
- AT Command Information 8
- Chapter 2 – Getting Started 9
- Surface 10
- Front Panel LEDs 11
- Functionality 12
- Using AT Commands 13
- Roaming Status 14
- Exiting Modem Mode 14
- Web Management Software 15
- Wizard Setup 16
- Set Time and Date 17
- Shutdown Caution 17
- Connecting to the Internet 18
- Chapter 3 – Using the Web 20
- Management Software 20
- Screen Parts 21
- Screen Buttons 21
- Submenus 21
- IP Setup 22
- General 24
- Authentication 24
- Submit 24
- General Configuration 25
- Time Zone Configuration 25
- Daylight Configuration 25
- IP Setup > Static Routes 26
- Remote Configuration 27
- PPP 28
- PPP General 29
- ICMP Keep Alive Check 29
- Submit Button 29
- PPP > Wakeup-on-Call 30
- PPP > Modem Commands 34
- Networks & Services 35
- Service Configuration 36
- Packet Filters 37
- DNAT Configuration 38
- Packet Filters > Advanced 40
- GRE Tunnels 41
- GRE Routes Configuration 42
- DHCP Server 43
- Tools 44
- Tools > Service Status 45
- Tools > Firmware Upgrade 45
- Statistics & Logs 47
- Commonly Supported Subnets 51
- The Antenna 53
- How to Change the Fuse 54
- Using External TFTP Client 55
- COMPANY/Policies/warranty/ 56
- Replacement Parts 57
- Electronic Equipment 58
Related products and manuals for Networking Multi-Tech Systems MTCBA-C-EN-NX
(22 pages)© 2020, manymanuals.com. All rights reserved. | 1.287 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals